Your shopping cart is empty
How To Wax A Surfboard:
Surfboard wax is used to help you stick to your board while surfing. The hard shell of a surfboard is slippery, which is good for the side in the water, but not good for under your feet. A good wax job creates bumps which give your feet something to grip to. If you’ve never waxed a surfboard before or you’re just looking for tips to get a better wax job, here is our guide to waxing your surfboard.
Step 1: What You Will Need
To wax your surfboard you will need a few supplies, mainly: basecoat wax, topcoat wax and a wax comb. If you are going to put wax on a used board or your are reapplying wax, you will also want some wax cleaner and a few paper towels.
Step 2: Clean The Surfboard
If you are waxing a brand new surfboard, you can skip to step 3. If you are waxing a used board or you are rewaxing your surfboard, it is important to first clean the deck. Any old wax on the board will sacrifice the integrity of your wax job and it will flake off earlier. You want to make sure that the basecoat is applied directly to the surface of the surfboard.
To clean it, first scrape off all of the wax with the straight side of your wax comb. Make sure to get any wax off of the rails by using the curved side of the wax comb. You then want to use a cleaning product to remove any excess wax. There is usually a thin layer of wax still remaining that you can see if you tip the board sideways in the light. Something like Chief Firewater will dissolve the excess wax and allow you to wipe it clean. Once your board looks glossy, you will know you have all of the wax removed and can begin putting on a new coat.
Step 3: Putting On A Basecoat
The basecoat is the most important step of waxing a board. The top coat of wax will get worn out and rub off as you surf but the basecoat will remain until the next time you completely rewax your board. If a patch of basecoat rubs off, you will have an area that is constantly without wax, even if you apply more top coat, it will rub off.
The goal of the basecoat is to create a bump pattern that will last. Basecoat surfboard wax is a harder wax which allows it to last longer, but also makes it a bit more difficult to apply so make sure to push down on the wax so some will rub off. If you press down too lightly, nothing will come off and it will take you a long time to wax. While waxing, your wax might skip along the surface making a strange sound, that is ok, it just means bumps are forming and the wax is bouncing over them. You will want to start by making broad strokes on the board and continuing until you see a bump pattern emerge.
There are many different techniques to apply wax, none is the correct way and you should do whatever works for you. As time goes on, you will find one that works for you. Some techniques to try as you get started would be:
Circles: Rub the wax in little circles, moving up and down the board.
Front to Back: Rub the wax in a straight line parallel to the rail.
Criss Cross: Go diagonal one way and then go perpendicular to that direction.
Psycho: Go every direction, make spirals, do whatever.
Once you see bumps begin to form, you will know you are doing it properly. Continue until you have created enough depth, or until you have used up the recommended amount of wax.
Step 4: Top Coat
The top coat of wax is much softer than a basecoat which allows it to be tacky and stick to your feet. Top coats are much more effected by the temperature of the water than a basecoat. Because of this you want to make sure to use a wax type that is good for the water temperature where you surf. Waxes come in temperature ranges marked on the label.
Waxes get softer when the water is warmer. To make sure the wax is at an ideal level of softness in a specific water temperature, different chemicals are added to the wax. A tropical temperature wax will be the ideal level of tackyness in warm water. A cold temperature bar of wax will be tacky even in cold water where most wax will have frozen up. However, if you take a cold temperature wax to warm water, it will be too soft. As a rule of thumb, you can always use a warmer wax in cold water, but don’t use a colder wax in warm water.
The top coat of wax will be applied in a similar way as the basecoat but since it is softer, you will not need to push down as hard. Like with the basecoat though, try a few things and eventually you will find something that works for you.
Step 5: After You Surf
When you surf a bit of the top coat will flake off. Some of it will end up in the water and some will be stuck on your wetsuit or board shorts. To account for this you will need to add a bit of wax before each time you go surf (or every few times if you’re lazy). Sometimes the wax will get really squished and look flat, if this happens, use the comb side of your wax comb to scratch diagonal lines into the wax, making a checkerboard pattern. This will ensure you stick to your board for a few sessions more.
If you have to do a lot of combing, it might be time to start over from scratch and put on a new basecoat. You should probably put on a new boasecoat every 3 months or so but at least once per year.